18+ How To Build A Pitcher's Mound

By building a pitching mound in your backyard, you will always be able to take some time out of your busy day to enjoy a catch with your son or daughter. No two areas of the diamond receive more abuse and constant wear than the pitcher’s mound and batter’s/catcher’s boxes.

Back yard hand built horse shoe pits with led lights

The pitcher’s mound the flat area atop the diamond, called the table, measures 5 feet wide by 34 inches deep.

How to build a pitcher's mound. With an edger or a spade, follow the outline and remove all inside turf to establish a permanent boundary for the mound. To build a standardized mound, the height needs to be 10 inches of which 2 foot is level section and 6 foot is the slope section. Why opt for a portable pitching mound;

The dimensions of the mound are 84 x 42. When the pitcher's front foot lands on the slope of the mound, the pitcher has more power behind the ball. Smooth the mound, rounding it out where needed, and fill any low spots.

The end with the pitching rubber is the full width of a 2x6 (~5 1/2 ) and it tapers down to 2 at the bottom. Once home, take both of your ten foot planks, mark off the two foot level sections (on opposing ends) and. Your logical side won't let you buy anything that you can make.

As you get ready to construct the mound, use the transit and laser (or string lines) to ensure home plate, the pitcher's mound, and second base are accurately aligned and that everything is square. But there should not be a pointed peak, instead there should be a level plateau at the top. Walk around the stake in a circle, keeping the string pulled tight, spraying landscaper’s paint to mark the circle as you go to create the outline of.

This will serve as your frame. Build your mound and plate right. Nail the plywood onto the frame.

The pitcher's mound is not supposed to be built up like a peak, but rather it should slope up to a firm and level plateau. Precisions matters, so measure for every step in the mound building process. A portable pitcher’s mound is a piece of equipment which comes in very handy during bad weather when practice needs to be moved to the nearest area with dry ground or indoor.

Six inches from the front edge of the table is the pitcher’s plate (also called the rubber), which measures six inches deep by 24 inches wide. Remember, the mound needs to slope properly. From the middle of the mound, the slope is supposed to decrease approximately one inch per one foot in each direction.

I also had them cut the 16' 2x10 into a 10 foot and 6 foot section. Building a portable pitching mound (for under $100) it's a curse being an engineer. Make each subsequent layer about 3 to 6 inches smaller in diameter.

Challenges of building a portable pitching mound; The first step you will need to take when looking to build a pitching mound in your backyard is to find a space large enough. Dig a trench 2″ deep and one shovel width wide around the inside edge of the mound.

As you prepare to construct the mound, use the transit and laser or string lines to make sure home plate, the pitcher’s mound and second base are accurately aligned and everything is square. Tamp the clay to a firm but level surface. I choose that height because in little league the mound is 6 above home plate.

Cut the plywood to the size that fits the length and width of your frame. If building a fully clay mound, dump clay and spread to shape. The flat section with the rubber is.

I decided to use a piece of 4' x 8' treated plywood as the main part of the mound. This will be filled with mound material and will prevent it from creeping past the edge of the mound circle during construction and compaction. Continue laying smaller and smaller diameter circles of mound clay on top of each other until the mound has reached the height marked on your stake in the center of the circle.

Build your mound, step by step. Moisten the mound throughout construction — it’s important that you keep the soil mixture moistened throughout the building of your pitcher’s mound. Since the rubber is 10” higher than the home plate, the plateau should be level with the rubber and span an area of 5’ by 3’.

Since the pitcher’s mound is exactly that, a mound, it is not perfectly flat. Why you should build a portable pitcher’s mound; Build in 2″ lifts, fully compacting with vibratory plate compactor or roller.

Drive a stake into the ground with a mallet at the center point of the pitcher’s mound. See more ideas about pitching mound, baseball pitching, baseball drills. Repeat steps 2 and 3 until the new surface is level with the old surface.

How to build the pitcher's plateau. Usually, these areas don’t have a pitcher’s mound so having a portable one could prove to be very useful. Typically, we recommend that the pitcher’s front foot lands on the mound.

Major league baseball (mlb) regulations call for the distance from the back of the home plate to the front of the pitching rubber to be 60 feet and 6 inches. Find a space large enough for your mound. For the base, i started with 4 1 x 10 x 10' pine boards.

So you now have two pieces of plywood, three ten foot boards and a six footer. Simple steps of constructing a portable pitching mound. Remove 2 to 4 inches of existing soil from the stress areas.lightly water.

How to Build a Pitching Mound! Pitching mound, Portable

Build a Pitchers Mound Brick design, Pitching mound

Share this post