41+ How To Measure Chain Size For Chainsaw

The rivets are the small, round pegs/studs that hold the chain segments together. To get the correct size, simply count 3 rivets on the chain and measure the distance between them from the centre points.

Universe of goods Buy "Durable Quality 16Inch Chainsaw

With your verniers first measure the 'wire size', that is the size of the wire that was bent to make into the links.

How to measure chain size for chainsaw. That’s how you can size a chain in a nutshell, but as you can see, there’s a lot to dig into. General chain lengths, like 18 inches, are not interchangeable. Now, measure the blade just where the blade is emerging from the casing of the saw.

Pitch is the measurement of the distance between the drive links in the chain, while gauge is the width of the drive links. A tape measure will provide that information. The gauge measurement is usually listed on the side of the chainsaw's bar in inches if you aren't able to measure it.

Pitch= the distance between 3 links divided by 2. Number of drive links, pitch, and gauge. To measure this, remove the chainsaw casing and measure the entire bar.

The 3 necessary chainsaw chain numbers the three necessary numbers for matching chains are: Steady the chainsaw on a flat surface, and begin measuring from the edge of the casing where the guide bar fits into the unit’s housing. Measure the distance from the tip of the chainsaw bar to the point where the bar first emerges from the saw’s casing.

Measure from the tip of the bar, to the end of the bar where it meets the motor. In this article, we will discuss the method of measuring a chainsaw chain. For 3/8lp and.325 pit chains, use 4.0mm (5/32”) file.

How to measure pitch size The proper size for a chainsaw Measuring a chainsaw chain is the process of determining the gauge and the pitch of a chainsaw chain.

Count the drive links — count the individual links on the chain one by one. Round up to the nearest inch. This will be one smaller than 16 inches.

If the measurement is an odd length, just round to the nearest even number, like 14″, 16″, 18″, etc. Or, if you are unsure about the real length, you can take it off, and. The most common pitch size for chainsaw chains is 3/8.

Well, you’re in luck, here’s how to measure a chainsaw chain: Find the cutting length of the chainsaw bar by laying a tape measure at the very tip of the chain. Keep the number from step three on hand to help purchase chain for the chainsaw.

The bar, the pitch, the number of driver links and the gauge. Number of drive links 1. Or in other words, measure the visible part of the bar that is capable of cutting.

This will give you how long the bar should be. Ideally, the measurement you get should range between 12 and 20 inches. If you’re responsible for light chores, you’ll need a smaller model.

Lay down the chainsaw on the surface and take a standard tape measure. Chains are usually made up of steel links that have been held together using rivets. That’s because chainsaw chains actually have three measurements:

As an example, three rivets that measure ½ an inch across divided by two gives you a pitch of a ¼ inch. Find the gauge of the chain by locating the number stamped on the drive link. Round the measurement up to the nearest inch.

Then, round up to the next even figure. The standard gauge sizes are 0.050 inches (1.3 mm), 0.058 inches (1.5. It is best to measure a few links just in case you grab a bum one, unlikely but possible.

There are 4 main elements you need to know, when measuring the chainsaw chain size: But if its pitch is 5.5mm (7/32”), you will need a 5.5mm flat file. Measure to the furthest tip.

To measure a chainsaw chain you need to find the pitch, gauge, and link count. For example, if the distance between 3 consecutive rivets on your chainsaw chain is 1 inch (2.5 cm), then the pitch would be this measurement divided by 2, or 1 ⁄ 2 inch (1.3 cm). Now divide this by half to get your size.

The most common pitch measurements you’ll find on a chainsaw chain. The second step to figuring out the perfect chainsaw size for your property is to think about the work you typically do. These are ideal for occasional light cutting, trimming, and pruning bushes, etc.

From the one end to the next. For 3/8 pitch chain, use a 4.8mm (3/16”) file. Round the measurement up to the nearest inch.

Measuring the replacement chain even without the product manual is simple, even if you don’t know anything about chainsaws for home use. This information can be found on the information stamp on the chainsaw bar, through the numbers on the chain, or through measuring your chain manually. Using a tape measure, carefully measure from the tip of the chain at the furthest end of the bar to the base where the guide bar enters the housing of the engine.

To determine the chainsaw bar size, simply take a tape measure to measure from the motor housing body, down the length of the bar to the tip of the bar. The other measurement you need is the entire length of the bar. A chainsaw chain or a cutting chain is an important component of any chainsaw.

This is the standard way of determining the measurement of a chainsaw bar. You are measuring the bar from side to side. To work out the pitch measurement you are going to need a tape measure.

This figure will usually be from 12 to 20 inches. Measure from the first to the third, then divide that. Measure from where the bar connects to the chainsaw casing to the furthest tooth of the chainsaw nose.

When you are measuring the chainsaw bar, it is actually easy. Also, another way to measure the chain length for a chainsaw is to start measuring the four elements on a chain. For the 404 pitch chain, the recommended is 5.5mm (7/32”) file.

The proper way for how to measure a chainsaw chain length is as follows: To measure the chain, you have to get two measurements, which are pitch and gauge. Select a few at random and not next to each other.

To determine the pitch (chain size), you'll need to measure the distance between any three consecutive rivets, then divide the result by 2. Take the measurement from the emerging point of the blade to the tip of the blade. Measure the area of the chainsaw where the bar comes out of the body.

What do the Numbers on a Chainsaw Chain Mean? (With images

How To Measure Chainsaw Bar Chainsaw bars, Cleaning wood

Share this post