50+ How To Read Degrees On A Plat Map

To read the coordinates of any location, start with the number of degrees on the latitude line, and clarify whether it is in the northern or southern hemisphere. So if 'q = deedpoints[0]', then 'q[0] = n' and 'q[5] = 1401.09'.

GIS to BIM ARCHICAD & Enzyme Building

100,000.” this ratio simply means that 1 unit of distance on the map is equal to 100,000 units in real life.

How to read degrees on a plat map. The earth is nearly 25,000 miles around, so once divided into 360 degrees, it means each degree is about 69 miles wide. I prefer the decimal format. Thence continue s 0 degrees 03’08” e, 409.67 feet;

So, to make our heading work, we need to add 36 to 180, giving us 216 degrees. Click on the remaining corners. For inches, divide the large number on the map scale (i.e.

You probably remember from school that a circle is 360 degrees, a degree is 60 minutes and a minute is 60 seconds. Our compass puts north at 0 degrees. For millimeters, divide the large number on the map scale (i.e.

The angle can be stated as a certain number of degrees (°), followed by an additional number of minutes ('), followed by a certain number of seconds (). The distances are usually indicated in u.s. The scale of your plat map will be in the map’s legend.

To better understand this concept, imagine that you are facing north. Sometimes a client will note that measured bearings and distances vary somewhat from the recorded measurements shown within the deed or on the plat. You miss figure the declination from the magnetic bearing shown on the plat by 2 degrees.

N42w, or 42 degrees west of north; This can be read more descriptively as north 66 degrees 0 minutes and 0 seconds for a distance of 1245.01 feet. Each degree is then broken down into 60 minutes.

Now click on the other parcel corners that interest you to see those coordinates. Thence run n 0 degrees. Read the compass degree system by starting with a specific point on the compass (north, east, south or west), and then reading the number of the degrees to the next point on the compass.

Use a ruler to get the most accurate reading of your plat map. The second format is degrees, minutes and seconds: Land survey maps are used to measure everything from.

A map’s scale provides a ratio of map distance to actual distance. Site plan is a drawing that is a bird’s Subdivision plats must be completed by a licensed surveyor and meet the survey plat recording requirements of 27 v.s.a.

As you continue to turn you would face west, located 90 degrees west of north. The scale will differ from map to map, but will typically be presented as a number ratio, like “1 : Directly to your right (east) would be 90 degrees east of north.

A survey bearing indicates the quadrant in which it exists and the number of degrees into that quadrant measured from zero. A site plan package can include: Learning to read a land survey map is not only for surveyors.

If your map shows seconds, find the second closest to where each line intersects the latitude or longitude scale at the edge of the map. If you turned around you would be facing south and would be 180 degrees south of north. Information relative to roads, lighting, landscaping, natural features, access, soil erosion control, and stormwater management.

For example, if your latitude line falls about 5″ above the 32°20′n line, your point is at a latitude of approximately 32°20′5″n. The elements of a list or a tuple are indexed by a number starting with zero. How to read a land survey map.

The corners of your plat map will have the book and page number. A plat is a map of a land area, usually on the scale of a neighborhood or county township, and a plot is a piece of land used for a single purpose (such as a park or a home). You read an old plat from the 40's with metes and bounds rounded to the nearest degree.

An example of bearing and distance might be n 66° 0′ 0″ e 1245.01′. For our 1:9,000 map example, the millimeter divide by number equals 1.8 (1 millimeter = 1.8 poles). Deedpoint is a list of tuples, while 'd' is a tuple.

For our 1:9,000 map example, the inches divide by number equals 45.5. The angle is calculated as degrees+minutes/60+seconds/3600. The scale will be the ratio between the distance on the map and the distance of the actual property.

Since south from there would be 180 degrees, 36 degrees does not make much sense. 4 degrees of error down one side of your parcel equates to about a 460' error in where you think the property corner should be. The plat is actually based on a previous plat drawn in 1850 so you're another 2 degrees off.

This reads north, 63 degrees east. surveyors can mark the compass degree system as precisely as they want. This will give you an idea of just how far you have to go. These are usually drawn and then each line is annotated with bearing and distance.

An example heading might be n63e. Survey plats can also be read in reverse. Thence n 89 degrees 54’41” w, 314.69 feet to the east line of a 20 foot easement;

Consider which format you want to use. This is then converted to cartesian degrees by the nested if/then.

From Dayton to Cambridge and Back Again the field notes

Geographic Information Systems The Missing Educational

Share this post